How to Remove Nissan Altima Car Stereo and Speakers
	Nissan Altima Car Stereo Removal
	Speaker Phasing Installing Aftermarket Speakers and Proper Hook-up
	NO AUDIO With aftermarket stereo installation?
	Erratic Volume Control DIY Repair
How to Remove Nissan Altima Front Tweeter 1.1) Pry top edge of side pillar panel releasing clips. All clips release with pry pressure.  2.1) Grasp top edge of side pillar panel. 3.1) Pull side pillar panel from car releasing all clips along edge of panel. 4.1) Grasp panel toward bottom. 5.1) Pull panel up to release bottom from front dash and remove. Note - there is a tongue on the bottom of this panel that fits into a groove in the dash, align tongue and grove when reinstalling panel. 6.1) Release trigger on connector at tweeter to disconnect. 7.1)) Pry edge of tweeter assembly to release clips. 8.1) Remove tweeter assembly. 9.1) When reinstalling side panel, weather stripping overlaps on edge of panel.
How to Remove Nissan Altima Front Door Speakers 1.1) Roll window down. 1.2) At door handle, locate panel at back of opening.  2.1) Lift trigger at center of back edge panel to release panel. 3.1) Pull edge of panel forward from opening. 4.1) Remove panel and set to side. 5.1) Remove exposed screw. 6.1) Locate pry opening on panel at bottom of hand hold on arm rest. 7.1) Remove panel and set to side. 8.1) Remove exposed bolt. 9.1) At top front edge of door panel, pry edge of small panel to release clip. All clips release with pry pressure. 10.1) Pull top edge of panel back releasing lower clips. 11.1) Remove panel and set to side. 12.1) Pry back edge of control panel up to release clip. 13.1) Lift back edge of control panel up releasing side clips. 14.1) Pull panel back to release front clips. 15.1) Remove control panel from arm rest for access to connectors. 16.1) Release trigger on connector to disconnect. 17.1) Release trigger on connector to disconnect. 18.1) Release trigger on connector to disconnect. 19.1) Remove control panel and set to side. 20.1) Remove exposed bolt from control panel cavity 21.1) Bottom back edge of door panel, pry edge of courtesy light from door releasing clips. 22.1) Remove courtesy light from door panel. 23.1) Release trigger on connector to disconnect. 24.1) Remove courtesy light and set to side. 25.1) Feed courtesy light connector into door panel. Note - remember to feed courtesy light connector back through door panel when reinstalling. 26.1) Pry back bottom edge of door panel from door releasing clips. 27.1) Pry along bottom edge of door panel then up front edge of door panel releasing clips. 28.1) Pull bottom edge of door panel away from door verifying all clips have been released. 29.1) Lift back edge of door panel up out of window jam. 30.1) Lift front edge of door panel up out of window jam. 31.1) Weather stripping along top edge of door panel may release from door panel during removal. 32.1) Bent tabs on weather stripping straight, align tabs with openings on door panel. 33.1) Place weather stripping into place and bend tabs under edge of door panel to secure. 34.1) Pull top edge of door panel back for access to door handle and lock cables. 35.1) Grasp edge of cable at mount. 36.1) Lift cable up to release from lock. 37.1) Pull cable around to align with opening at end of linkage. 38.1) Lift end of linkage up to release and remove. 39.1) Grasp second cable. 40.1) Lift cable up to release from lock. 41.1) Pull cable around to align with opening at end of linkage. 42.1) Lift end of linkage up to release and remove. 42.1) Remove door panel and set to side. 43.1) Check door for any remaining door panel clips. 44.1) Pry clips from door to remove. 45.1) Place clips into corresponding slots on door panel ready for reinstallation. 46.1) Release trigger on connector at speaker to disconnect. 47.1) Remove bolts securing speaker to door, remove speaker. 48.1) When reinstalling cables, place end of cable into slot and push cable mount down into slot to lock in place.
Car Stereo Repair Home | Car Stereo Removal | Contact | Books 4 You