DIY Chrysler 300 Car Stereo and Speaker Removal
	Chrysler 300 Car Stereo Removal Guide
Chrysler 300 Front Door Speaker Removal Chrysler 300 Front Door Speaker Removal Instruction Guide 1.1) ROLL WINDOW DOWN. 1.2) Along back edge of door panel, locate door panel pin. 2.1) Push center pin on door panel pin in to stop. 3.1) Gently pry behind edge of panel to release pin. 4.1) Remove door panel pin and set to side. 5.1) To reinstall door panel pin when reinstalling door panel, push center pin back through pin approximately 1/4 inch. 6.1) Push pin back into opening on door panel until outside ring is flush with door panel. 7.1) Push center pin in flush with outer ring locking into place. 8.1) Along back edge of door panel, locate door second panel pin. 9.1) Push center pin on door panel pin in to stop. 10.1) Gently pry behind edge of panel to release pin. 11.1) Remove door panel pin and set to side. 12.1) Remove third pin along lower rear edge of door panel. 13.1) Remove three screws along bottom edge of door panel. 14.1) Remove one screw along bottom front edge of door panel. 15.1) Remove lower door panel pin along front edge of door panel as described in earlier steps. 16.1) Remove upper door panel pin along front edge of door panel as described in earlier steps. 17.1) Gently pry top edge of small cover from door panel under arm rest. 18.1) Remove exposed screw. 19.1) Gently pry top edge of small cover from door open handle cavity. 20.1) Remove exposed screw. 21.1) Pull back of door panel from door releasing clips along back edge and top edge of door panel. All clips release with pressure. 22.1) Pull front of door panel from door releasing clips along front edge and top edge of door panel. 23.1) Pull entire door panel slightly from door. 24.1) Lift back edge of door panel up over door lock. 25.1) Pull top edge of door panel back away from door. 25.1) At back of door panel, locate door open handle linkage. 26.1) Twist small plastic lock on linkage to side. 27.1) Lift linkage end up out of opening to release linkage from door panel. 28.1) Locate wire bundle secured to door panel. 29.1) Pull on each side of wire bundle to release clip. 30.1) On back of door panel, at leading edge of door panel, release trigger on connector to disconnect and remove. To release triggers at center of connector locate trigger, squeeze trigger into connector to release and remove connector. 31.1) Release trigger on second connector at control panel and remove. 32.1) Release trigger on third connector at control panel and remove. 33.1) Release trigger on connector at seat memory switch and remove. 34.1) At bottom front edge of door panel, release trigger on connector at courtesy light and remove. 35.1) Follow wire bundle for courtesy light back to securing clip. 36.1) Grasp wire bundle on each side clip and pull to release from door panel. 37.1) At control box, bottom center of door panel, release trigger on first connector to disconnect and remove. 38.1) Release trigger on next connector to disconnect and remove. 39.1) Release triggers on remaining connectors to disconnect and remove. 39.2) Remove door panel and set to side. 40.1) Check door for remaining door panel clips. 41.1) Pry door panel clips from door to release. 42.1) Place door panel clips back into slot on door panel ready for reinstallation. 43.1) Remove screws from speaker to disconnect and remove.
Chrysler 300 Front Dash Speaker Removal Installation Chrysler 300 Front Dash Speaker Removal Instruction Guide 1.1) Gently place small pry tool between edge of front dash speaker grill and surrounding dash. 2.1) Pry speaker grill from dash releasing clips. All clips release with pressure. 3.1) Work around speaker grill releasing clips. 4.1) Remove speaker grill cover. 5.1) Remove two screws securing dash speaker. 5.2) Remove speaker from dash and disconnect.
Car Stereo Repair Home | Car Stereo Removal | Contact | Books 4 You